4,6-二氯嘧啶合成工艺研究

4,6-二氯嘧啶是一种重要的化工中间体.研究了反应温度、溶剂种类、催化剂种类、催化剂用量和反应物投料配比在4,6-二氯嘧啶合成过程中对反应的影响.结果 表明,在以邻硝基甲苯为溶剂,苄基三乙基氯化铵为催化剂,且催化剂用量为4,6-二羟基嘧啶质量的2％,n(4,6-二羟基嘧啶):n(三光气)=1∶0.8,反应温度为100～110℃的最佳条件下,产品收率可以达到93.4％.     

Mechanical properties and thermal shock in thin ZrO2–Y2O3–Al2O3 films obtained by the sol-gel method

Thin multilayer coatings of ZrO₂–Y₂O₃–Al₂O₃ were prepared using the sol-gel method and dip-coating technique in order to advance in the study of what influence the incorporation of Al₂O₃ has on films of Y₂O₃-doped ZrO₂, investigating its role in the synthesis of the solutions and in the characteristics and properties of the coatings. After the characterization of the solutions used in the process, the microstructure of the films was studied and their mechanical behaviour and resistance to thermal shock were determined so as to optimize the characteristics and functionality of these coatings. With increased alumina content, 3YSZ-Al₂O₃ (20 mol%), the cubic phase of the zirconia disappeared completely at the sintering temperature used (700 °C), resulting in the tetragonal phase with Al in solution. There was also a decrease in the coatings' hardness and Young's modulus, and an increase in toughness and resistance to thermal shock. These results allow guidelines to be established for the design of multilayer structures that are, tougher, more resistant, and have improved surface properties.     

Characterization of precipitates formed in X7R 0603 BME-MLCC during sintering

In the current study two different batches of X7R-0603 BME-MLCCs displayed dissimilar electrical performance, despite having the same chemical composition, tape casting, and sintering conditions; with the only difference between them being the ore deposits where the raw materials were extracted from to synthesize the BaTiO₃. Specifically, they presented different electrical response to highly accelerated life tests (HALT). Although the chemical analysis of each slip showed the same composition, the trace elements of the BaTiO₃ sources could have acted as dopants or produced different secondary phases. A search for precipitates in the two samples was conducted by means of Scanning (SEM) and Transmission Electron Microscopy (TEM) techniques. SEM observations confirmed the presence of precipitates formed within the structure of the MLCCs exhibiting the greatest decrement in their electrical resistance results during the HALT. In order to further characterize the observed precipitates, samples were prepared by Focused Ion Beam (FIB) lift-out method, to make TEM characterization of specific precipitates feasible. TEM studies were performed on the precipitates to obtain electron diffraction patterns and complementary Energy Dispersive X-Ray Spectroscopy (EDXS) chemical analysis. Based on the crystal and chemical data obtained, it can be concluded that the precipitates are a hexagonal anhydrous silicate oxyapatite phase with a stoichiometry of Ca₃Y₁₆Si₁₀O₁₃, and lattice parameters of a = 0.9353 nm and c = 0.6970 nm; this phase was not found in the JCPDS data base. Differences in raw materials coming from different ore deposits can produce undesired precipitates that affect the electrical performance of MLCCs.     

Centrifugally spun carbon fibers prepared from aqueous poly(vinylpyrrolidone) solutions as binder-free anodes in lithium-ion batteries

Aqueous solutions of poly(vinylpyrrolidone) (PVP) of various concentrations (20, 25, and 28 wt%) were successfully spun into fibers by centrifugal spinning. The pristine PVP fibers were annealed and carbonized to produce flexible carbon fibers for use as binder-free anodes in lithium-ion batteries. These flexible carbon fibers were prepared by developing a novel three-step heat treatment to reduce the residual stresses in the pristine PVP precursor fibers, and to prevent fiber degradation during carbonization. The thermogravimetric analysis data showed that the annealed fibers yielded a residual mass percentage of 36.0% while the pristine PVP fibers suffered a higher mass loss and only retained 26.5% of original mass above 450 °C (under nitrogen). The electrochemical performance of the carbon-fiber anodes was evaluated by conducting galvanostatic charge/discharge, rate performance, and cycle voltammetry experiments. The 20, 25, and 28 wt% derived binder-free anodes delivered specific charge capacities of 205, 189, and 275 mAh g⁻¹, respectively, after the first cycle at a current density of 100 mA g⁻¹. The results obtained in this work indicate that a feasible pathway towards a large-scale production of carbon-fiber anodes from a 100% aqueous solution can be achieved via centrifugal spinning and subsequent heat treatment.     

乘用车悬架静强度与疲劳载荷研究

为了快速获得平台悬架静强度与疲劳载荷,本文依据某A级平台5款量产车型试验场道路栽荷数据,以前麦弗逊悬架为研究对象,先对轮心载荷幅值进行统计分析,根据应力-强度干涉模型,得到该平台前悬架的强度载荷边界,及其与车辆满载轮荷的G载荷系数.再通过研究5款车型车轮轮心疲劳伪损伤与轮荷的关联关系,得到该平台悬架的疲劳栽荷.此方法可快速获得同平台悬架静强度与疲劳载荷,省去实车道路谱采集并提升了工作效率.     

机井自动化供水方案改进

针对民乐县农村人饮机井水位自动供水系统控制中存在的可靠性低、成本高等问题,文章结合深井泵提取地下水进行供水的实际情况,提出了软启动控制柜+浮球开关+微电脑时间控制器改进的思路和方法,运用效果良好。     

具有良好时频性能的电力系统次同步振荡模态在线辨识算法

介绍了一种适用于电力系统次同步振荡在线监测的非平稳信号模态辨识算法,该算法综合了经典IIR窄带滤波器组算法及经验模态分解(empirical mode decomposition,EMD)算法的优点,利用次同步振荡分析获得的预知频率信息,对可能导致模态混叠的相邻模态做数字滤波器(Infinite Impulse Response,IIR)预处理,再经EMD获得无混叠的固有模态分量IMF1.该算法具有理想的窄带选频特性,且能够快速反映次同步振荡及机组扭振发生最初的时域过程,计算量很小,可用于现场在线提取SSO模态特征,有利于更好地实现对次同步振荡的稳定性判别及闭环控制、机组扭振保护等.最后,利用PSCAD产生的仿真数据及某电厂发生次同步振荡的现场数据验证了该算法的有效性.     

机器翻译译文质量估计综述

机器翻译译文质量估计(Quality Estimation,QE)是指在不需要人工参考译文的条件下,估计机器翻译系统产生的译文的质量,对机器翻译研究和应用具有很重要的价值。机器翻译译文质量估计经过最近几年的发展,取得了丰富的研究成果。该文首先介绍了机器翻译译文质量估计的背景与意义;然后详细介绍了句子级QE、单词级QE、文档级QE的具体任务目标、评价指标等内容,进一步概括了QE方法发展的三个阶段: 基于特征工程和机器学习的QE方法阶段,基于深度学习的QE方法阶段,融入预训练模型的QE方法阶段,并介绍了每一阶段中的代表性研究工作;最后分析了目前的研究现状及不足,并对未来QE方法的研究及发展方向进行了展望。